High Speed Machining VI.

Intro -- High Speed Machining VI -- Preface, Committees and Sponsors -- Table of Contents -- Chapter 1: Mechanisms and Machining Process -- Research Progress of High Speed Cutting for SiCp_Al Composite Materials -- Experimental Study of the Corner of Hardened Steel Mould in High Speed Milling with Micro-End Mill -- Experimental Study on Surface Quality at Different Milling Speed of High Volume Fraction SiCp/Al Thin Walled Test-Piece -- Research on Tool Wear of PCD Micro End Mill in Machining of ZrO2 Ceramics -- The Machinability Comparison of Laser Solid Forming (LSF) and Forging TC4 Alloys -- Milling Forces of Compacted Graphite Iron (CGI) and Gray Iron (GI) -- Bioactive Film Generation during Titanium Alloy Cutting in Oxygen-Enriched Atmosphere -- Investigation of Cutting Force and Tool Wear in High Speed Milling of GH4169 Using Ceramic Tools -- Investigation on Processing Technology in Machining CFRP Large Size Hole -- Milling Force Modeling and Experimental Research of 300M Ultra High Strength Steel -- Defects Study on Drilling of Carbon Fiber Reinforced Polymer (CFRP) Laminates -- Experiment on Magnetization of High-Speed Steel Cutting Tool -- High Temperature Alloy of Turning Processing Characteristic and Process Analysis -- Experimental Study on Orthogonal Cutting of 0° T700/LT03A CFRP Uniform Laminates -- Experimental Investigation of Tool Wear and Chip Morphology in Turning Titanium Alloy Ti6Al4V -- Research on the Cutting Property of Ceramic Tool Cutting Nickel Based Superalloy GH4169 -- Investigations on the Machinability of Titanium Alloy TC25 -- An Experimental Study on Optimization of Cutting Parameters for Disk Milling Titanium Blisk -- Research on the Wear Process of High Speed Cutting Ni-Based Superalloy -- Experiment Research on Chips Flying Characteristics for Heavy-Duty Milling.

Investigation of Chip Morphology in High-Speed Milling of Nickel-Based Superalloy GH706 -- Study on Drilling Characteristics of Supper Alloy GH3039 -- Effect of High-Temperature Alloy Cutting Speed on Tool Wear -- Determination of Unit Cutting Force of GH4698 Broaching -- Investigation on Milling Force with Tilt Angles in Milling Cr12MoV -- Application of High Speed Machining Technology in Modern Die Manufacture -- Study on Force Characteristics for High Speed Sawing of Quartz Glass with Diamond Blade -- Chip Formation in High-Speed Milling of Titanium Alloy with PCD Tools -- Research on Wear Surface Morphology of PCBN Tools in High-Speed Machining Valve Seat Insert -- Surface Roughness Prediction and Experimental Analysis in Grinding the Material of Zirconia Used by Dental Restoration -- Research on Micro Machining of Slit Grating -- Cutting Force Analysis in Tool Condition Monitoring of Difficult to Cut Materials -- Investigation of Tool-Wear and Surface Roughness in Turning Ti6Al4V under Different Cooling Lubrication Conditions -- Research on Fractal Characterization in Grinding of Monocrystal Sapphire -- Experimental Study on Turning Nickel-Based Superalloy GH4033 with Coated Cemented Carbide Tools -- Study Chip Breaking Experimental and Optimal Design of Tool for Machining Cylindrical Shell Material -- Silicon Carbide Ceramic Turning Process Design and Parameter Analysis -- Turning Test and Simulation of Difficult to Cut Materials 300M in Aviation -- Cutting Performance and Wear Mechanism of Coated Silicon Nitride Cutting Tool in Turning of High Hardness Alloy Steel -- Research of Dynamic Cutting Force in Hardened Steel Precision Turning Process -- Changing Boundaries of Serrated Chip in Hard Cutting GCr15 Steel -- Experiment Research of Milling Force in High Machining GH4169 Based on MatLab.

An Experimental Study of Cutting Force on Large Cutting Depth Turning Titanium Alloy with CBN Tool -- Chapter 2: Modeling and Simulation of Machining Processes -- Milling Force Prediction for Circular Contour Machining -- The Mathematic Model of End Mill's Rake Face Based on the Fillet and Two Attitude Angles of Grinding Wheel -- Prediction of Cutter-Workpiece Engagement for Five-Axis Ball-End Milling -- Finite Element Simulation of Hardened Steel Cutting Based on DEFORM-3D -- The Minimum Cutting Thickness in Milling Process Simulation Analysis -- Finite Element Simulation Research on a Large Cutting Depth and Quasi-High Speeds 3-D Milling of Titanium Alloys -- Applying Genetic Algorithm and BP Neural Network Model to Predict Cutting Area Temperature Distribution in the Laser-Assisted Milling -- Finite Element Analysis of Tree Groove Broaching Rebound -- Cutting Force Prediction of Disc Cam Contour Milling -- Study on Finite Element Simulation of the Influence of Cutting Speed on Chip Formation of SiCpAl Composites in High Speed Milling -- High-Speed Machining Time Model Prediction of Combination Framework Based on BP Neutral Network -- Finite Element Method Simulation Study of High-Temperature Alloy Serrated Chip -- Finite Element Simulation and Experiment on Residual Stress in Turing 45# Steel with Complex Groove Tools -- Research on Mold Steel Minimum Cutting Thickness Based on ABAQUS -- Finite Element Simulation on Tool Strength of Rough Turning Cylinder -- Simulation Studies of the Cutting Process on SiCp/Al Composites with Different Volume Fraction of Reinforced SiC Particles -- Finite Element Analysis of Dynamic Characteristics of the Machine on Multi-Position Conditions -- Analysis of Microscopic Damage of Hardened Steel Milling Surface on Mould Service Process -- Modeling and Simulation of Ball End Milling Force for Mold Cavity Corner.

The Impact of Hardened Steel Milling Surface Structure on Mould Service Load -- Three-Dimensional Finite Element Analysis in Plunge Milling for Stainless Steel -- High-Speed Cutting Finite Element Model Parametric Modeling Based on ABAQUS -- Forecast of Limit Cutting Depth for Hardened Mould Steel Milling -- A New Conversion Matrix Model of Strain-Gage Dynamometer -- FEM-Based Prediction and Control of Milling Deformation for a Thin-Wall Web of Ti-6Al-4V Alloy -- Simulation of Machining of Incoloy 907 Based on Thermodynamics -- FEM Analysis of Residual Stress Distribution and Cutting Forces in Orthogonal Cutting with Different Initial Stresses -- DEM Simulation of Ceramic Tool Abrasion in Machining Superalloy -- Performance Analysis of the Multi U-Shaped Bellows Based on CAE -- Research on Automatic Nesting Algorithm Based on Heuristic Search -- The Development of an Automatic Leather Nesting System -- Numerical Modeling of Minimum Uncut Chip Thickness for Micromachining with Different Work Materials -- Modal Analysis of High-Speed Face Milling System Based on Composite Structure System Analysis Method -- Chapter 3: Machine Tools and Cutting Tools -- Determination of Capto C5 Shank's Key Dimensions -- Edge Preparation on Cutting Force, Cutting Temperature and Tool Wear for Hard Turning -- Mechanical Properties and Microstructure of TiN-TiB2 Composite Ceramic Cutting Tool Material -- Application of Tool Compensation in CNC Machining -- Investigation on Performance of a CVD Coated Carbide Tool in Face Milling of Ultra-High Strength Steel 30Cr3SiNiMoVA -- Tool Wear Identification in Turning Titanium Alloy Based on SVM -- Cutting Performance of Diamond Coated, TiAlN Coated and Carbide Cutting Tools in High Speed Milling Graphite -- Experimental Research on the Selection of Tool Material in Turning Superalloy GH4169.

The Milling Cutter Design and Simulation for Complex Cavity Machining -- CSPAID: Cutting Tool "Shape-Performance-Application" Integrating Design Approach -- An Investigation of Wear of Ball End Milling Cutter for High-Speed Milling of Hardened Cr12MoV Steel -- Circular Milling Cutter Design and Finite Element Simulation for Machining Hardening Steel Mould -- Parametric Design of Ball-End Milling Tools for High Speed Milling -- Study on Dynamic Properties of Damping Boring Bar with Large Ratio of Length to Diameter -- Cutting Edge Mathematical Model for Ellipsoidal End Mill -- Studies on Ceramic Cutting Tool Wear for the High Speed Milling Nickel-Based Superalloy -- Application and Technology Research in Deep-Hole Drilling System -- Fabrication and Mechanical Properties of Homogenous and Graded Si3N4/(W, Ti)C Nano-Composite Ceramic Tool Materials -- Design Method of Assembly Accuracy Repeatability of Heavy Duty Machine Tool -- Control Strategy for Hydraulic Hybrid Servo Drive System of Heavy Load Robot -- Study on the Tool Wear of Coated Carbide Tool in High Speed Milling Titanium Alloy -- Research of an Open CNC System of Machine Tool for Finding and Repairing Surface Damage on KDP Crystal -- Research on the Floating Motion Platform for Detecting Surface Defects in KDP Crystal -- Numerical Modelling of Liquid Bearing Utilizing Traveling Waves by Using OpenFOAM -- Experimental Study of Tool Wear during Quasi High Speed Turning Titanium Alloy with Large Cutting Depth -- NC Wedge-Caulking Special Machine Tool Design -- Study on Capacity of Vertical Lathe for Heavy Hydrostatic Bearing -- Development and Experimental Verification of an Innovative Non-Contact Liquid Bearing Utilizing Traveling Waves -- Chapter 4: Surface Integrity of Machining Processes -- Experiment Study of Serrated Chip and Surface Roughness of High Speed Cutting of Ti6Al4V.

Experimental Investigation on Surface Roughness in Precision Cutting Ti6Al4V Alloy Using Diamond Tools.

Selected, peer reviewed papers from the 6th International Conference on High Speed Machining (ICHSM 2014), July 24-25, 2014, Harbin, China.

Description based on publisher supplied metadata and other sources.

Electronic reproduction. Ann Arbor, Michigan : ProQuest Ebook Central, 2024. Available via World Wide Web. Access may be limited to ProQuest Ebook Central affiliated libraries.