TY  - BOOK
AU  - Jiang,Zheng Yi
AU  - Liu,Xianghua
TI  - Advances in Materials and Materials Processing V
T2  - Advanced Materials Research Series
SN  - 9783038268178
AV  - TS183 -- .I584 2015eb 
PY  - 2015///
CY  - Zurich
PB  - Trans Tech Publications, Limited
KW  - Electronic books
N1  - Intro -- Advances in Materials and Materials Processing V -- Preface and Committee -- Table of Contents -- Chapter 1: Composites -- Analysis of the Geometry and Microcracks of Kevlar/Epoxy Composites -- Effect of Diamond Shape on Surface Roughness of Diamond/Cu Composites -- Effect of Diamond Shape on Thermal-Physical Properties of Diamond/Cu Composites -- Effects of Sintering Temperature on Microstructure and Wear Properties of Al2O3 Particle Reinforced Al Composites -- Preparation of Nickel-Based Al2O3-TiB2 Composite Ceramic Powder -- The Influence of Sintering Temperature and Whisker Content on the Flexural Strength of Aluminum Borate Whisker Reinforced Aluminum Phosphate Composite Materials -- The Study of Composite Material of Al-C System -- Chapter 2: Low-Dimensional and Nano-Materials -- Atomistic Simulation on Buckling Behavior of Monolayer Graphene -- Modeling and Simulation for Current-Illumination Characteristics of Carbon Nanotube -- Preparation and Thermal Fatigue Behaviors of Silicon Nitride Nano-Ceramics -- Study on Dispersion and Rheology of Particles in Water-Based Nano TiN Fluid -- Transmission Performance of Water-Based Nano Fluid Based on Computational Fluid Dynamics -- β-Cyclodextrin Modified Hybrid Magnetic Nanoparticles as an Adsorbent for Phenol Removal -- The Preparation of ZrO2 and the Influence of the Calcination Temperature -- The Synthesis of Single-Crystal BiOI Nanoplates with {001} Facets Exposed -- Chapter 3: Metal-Based Materials and Alloys -- A Study on Mechanical and Fatigue Properties of a Stainless Steel -- Development of 590MPa Grade Hot-Dip Galvannealed DP Steels -- Effect of Annealing Temperature on Microstructure and Damping Capacity of Twin Roll Cast ZK60 Alloy -- Effect of Ca and Nd Alloying on the Microstructure of Mg-6Al-Ca-Nd Alloy; Effect of Cu on the Electrochemical Corrosion Behavior of Sn-8Zn-3Bi Lead-Free Solder Alloy -- Effect of Electropulsing Rolling on the Microstructure and Properties of Industrial Pure Titanium TA1 -- Effect of Er on Microstructure and Hardness of Al-Zn-In Alloy -- Effect of Grain Size on Microstructure and Orientation of Fe-25Mn-3Si-3Al Steel -- Effect of Nd on Primary Silicon and Mechanical Properties of Hypereutectic Al-17.5%Si Alloy -- Experiment and Analyses on 16 Mn Steel under Cyclic Loading Controlled by Strain -- Experimental Study on the Effect of Retained Austenite on the Impact Toughness of a Low-Carbon Martensite Steel -- Galvanic Corrosion of 70-30 Copper-Nickel Alloy in Contact with Nickel-Aluminum Bronze in Simulated Deep Sea Environment -- High Temperature Oxidation Investigation of Hot Roll Material with High-Speed Steel -- Influence of Neodymium on Wear Resistance of Hypereutectic Al-Si Alloy -- Influence of Pre-Deformation Strain on Recovery Performance of Ni47Ti44Nb9 Alloy Φ8mm Pipe Joint -- Influence of Solution Treatment on the Microstructure and Mechanical Properties of an Deformed Al-12.7Si-0.7Mg Alloy -- Investigation on the Property of High Si-Al Alloy Prepared with Ultrasonic Vibration Aided Casting Technology -- Isothermal Crystallization Behavior of Cu42Zr42Al8Ag8 BMG Investigated with Electrical Resistance Measurement -- Liquid-Phase Separation of Undercooled Fe-Cu-Si Alloy -- Manufacturing Technology Research of Magnesium Alloy Transmission Case -- Measurement of TTP Curves of 7050 Aluminum Alloy by Conductivity -- Micromechanics Analysis of Elastic Modulus of Alumina-Carbon Refractories -- Modification of Hypereutectic Al-20%Si Alloy by Neodymium -- Research on Heat Resistance of As-Cast Ferritic Nodular Iron -- Study on High-Temperature Mechanical Properties of SPHC Steel Produced by CSP Technology; Study on Microstructure and Property of High Boron Alloyed Stainless Steel Composite Plate Containing Titanium -- Study on Multi-Alloy Ingots Produced Using Hot-Top DC Casting Approach -- Test and Research on Ratchet Effect of 16 Mn Steel under Cyclic Loading -- The Feature of Slag from Complex Hot Metal Blown by Converter Processing and its Influence on the Craft -- The Phase Structures and Properties of Pt-Ir-M (M=Zr, Mo, Y) System -- Determination of Al, Cu, Ni in Zr-Based Amorphous Alloy by Inductively Coupled Plasma Atomic Emission Spectrometry -- Ti-Al-Zr-B-Y Amorphous Alloy Powders Prepared by Mechanical Alloying -- Chapter 4: Building and Construction Materials -- Comparison and Analysis of RC Beams Strengthened with FRP Bonded on the Side and Bottom Surface -- Effect of Basalt Fibers on Rheological Property of Asphalt Mortar -- Experimental Research on Anti-Cracking Ability of Polyacrylonitrile Fiber Mortar -- Experimental Study of Influences of Initial Temperature on Cement Grout Performance -- Impact of Composite Mineral Admixture on Carbonization Resistance of High Performance Concrete -- Influence of Layered Materials on Properties of Cement Stabilized Macadam -- Inversion of Material Parameters of Composite Fiberglass Box Structure -- Mechanical Properties of High Strength Desert Sand Concrete -- Nonlinear Structural Analysis of Fire-Exposed Reinforced Concrete Column -- Research on Separation and Regeneration Aggregate of Recycled Asphalt Mixture Road Performance -- Comprehensive Evaluation of Asphalt-Mixture Performance Based on Principal Component Analysis -- Chapter 5: Biomaterials and Technologies -- A Comparison of Gelling Properties Stability of Dry-Heating and Maillard-Type Egg White Proteins -- Fabrication an Antibacterial Surface on Composite Porous Scaffold; Investigation of the Surface Modification on Biomedical Magnesium Alloy -- Nonenzymatic Glucose Electrochemical Oxidation Based on Pt Decorated MWCNTs-PVA Hybrid Electrode -- RSM as an Approach to Optimize Ginger Intermittent Microwave Drying Process -- Study of the Degradation Behaviour of Biomaterial Mg-4.0Zn-2.0Sr Alloy in SBF -- Synthesis and Characterization of the Bio-Based Oligomer -- The Influence of the Addition Element of Zn and Sr to Degradation Behavior of Pure Magnesium -- Electrospun Hydroxyapatite/BMP-2 Grafted PLLA Nanofibers for Guided Bone Rebuilding Scaffold -- Chapter 6: Chemical Materials and Technologies -- Effect of Dimethyl Sulfoxide (DMSO) on Cellulose Solution with High Concentration -- Flexible Graphene Paper as a Binder-Free Anode Material for Lithium Ion Batteries -- Highly Selective Separation and Enrichment of Phosphopeptides by Uranyl-Salophen Immobilized Silica Gel Material -- Influence of Co(ii) Ionic Liquids Catalytic System for Polycarbonate (CHO/CO2) Synthesis -- Preparation of Sodium Paeonolsilate Intercalated into Layered Double Hydroxides and its Release Properties -- Preparation of Zeolite from Waterworks Sludge for Ammonium Ion Removal in Wastewater -- Radical Polymerization of a Novel Methacrylamide Derivative -- Simulation Study of the Volume Properties and Diffusion of 1-Butyl-3-Methylimidazolium Tetrafluoroborate/Ethanol Mixture -- Sorption of Pb(II) on Iron Hydroxide Modified Diatomite -- Synthesis and Application of the Three-Component Lyotropic Liquid Crystal -- Synthesis and Characterization of Thiol Functional Cyclic Carbonate -- Synthesis and Crystal Structure Hindered Amine with Methaerylate -- Synthesis of Hyperbranched Polyphenylacetylene Resins and the Influence of their Molecular Architecture on their Properties -- The Application of Dye Materials on Efficient Visible Light Photocatalysis; Biomineralization-Inspired Synthesis for Hierarchical Structured ZnO Powders with Enhanced Potocatalytic Activity -- Evolution of Phase Structure and Micro-Morphologies of the La0.7M0.3MnO3 (M=Ca, Sr) Sintered at Different Temperature -- Study of Salen(Al) Complex Catalytic System in Ring-Opening Polymerization of Lactide -- Conversion of Chitosan into 5-Hydroxymethylfurfural via Hydrothermal Synthesis -- Density Functional Studies on the Standard Heats of Formation for Nitroaromatic Molecules -- Influence of Cadmium Oxide on Thermal Hazard of AP-CMDB Propellants -- Swelling Kinetic Study of Poly(Vinyl Alcohol)/Poly(γ-Glutamic Acid) Blend Hydrogel -- Chapter 7: Material Testing, Characterization and Applications -- Analysis of Impact of Moisture Content on Rock Thermal Conductivity Coefficient Using TCS Method -- Effect of Surface Treatment on the Stress Corrosion Cracking of 304 Austenitic Stainless Steels in Acid Chloride Solution -- Fatigue Properties and Fracture Characteristics of the Aluminum Alloys for High-Speed Train Carbody -- Influence of Predeformation on Mechanical Behavior of Hastelloy C-276 -- Iron Temperature Field Finite Element Analysis and Measurement Verification -- Lifetime Estimation of Chain Plates for Floodgates Working in Seawater by Continuum Fatigue-Creep Damage Theory and Transient Analysis of Diffusion Process of Hydrogen -- Qualimetric Evaluation of Aluminum Wire Deformed by a Combined Scheme of Deformation "Pressing-Drawing" -- Strength Testing of Fabric Composite Material and Impact Simulation for Airbag Landing System -- Study of Influence Factors on Medium-Density Fiberboard Thermal Analysis -- Study on Testing Methods for Thermophysical Properties of Materials -- The Estimation of the Thermal Properties of Refractory Materials According to the Temperatures Acceleration Curve at the Blast Furnace Blowing-In; The Evaluation of Absorption Performance of Magneto-Rheological (MR) Elastomer
N2  - Selected, peer reviewed papers from the 2014 5th International Conference on Advances in Materials and Manufacturing (ICAMMP 2014), December 20-21, 2014, Fuzhou, China
UR  - https://ebookcentral.proquest.com/lib/orpp/detail.action?docID=2008458
ER  -