TY - BOOK AU - Murariu,Alin Constantin TI - Innovative Technologies for Joining Advanced Materials T2 - Advanced Materials Research Series SN - 9783038266242 AV - T173.8 .I584 2014 U1 - 600 PY - 2014/// CY - Zurich PB - Trans Tech Publications, Limited KW - Technological innovations-Congresses KW - Electronic books N1 - Intro -- Innovative Technologies for Joining Advanced Materials -- Preface, Organizing Committee, Reviewers and Sponsors -- Table of Contents -- 3D Simulation of Stress-Strain State of Plasma Arc Surfacing by CAD/CAE Software Sysweld -- Methodology for Reparation of Damaged Sleeves and Welded Shield Sections of Guide Vanes at Hydropower Plant DJERDAP 1 -- Analysis of Current State and Integrity Evaluation for the Supply Tank of Generation Unit 6 of Thermal Power Plant Nikola Tesla "A", Obrenovac -- Research on Argon Protection when Using WIG Welding -- Ways of Numerical Prediction of Austenitic Grain Size in Heat-Affected Zone of Welds -- Application of Numerical Simulations at Welding Multilayer Welds from the Material X22CrMoV12-2 -- Enhanced Joint Properties by Magnetic Pulse Crimping with Filler Material -- Alternate Design Solutions for Reduced Stress Concentration Factor (SCF) T Joints of Circular Hollow Structures -- Characterization of Plasma Cut Surfaces with Water Bed Welding Metallic Materials -- Weldability of Magnesium and Aluminum Alloys Using Nd-Yag Laser -- Reconditioning by Welding of Rims Manufactured from Nonferrous Alloys -- Tenacity Evaluation of the Deposited Metals by Welding, Using 3Si-2 Wire of ΓΈ1.2 mm on S355J4 Steel -- Composite Rods for Brazing -- Nanostructured Materials for Cladding by Welding -- Development of a New Generation of Welding Simulators for Education and Training -- Estimating the Reliability for Asphalt Milling Machines Teeth Manufactured by Claddings Processes -- The Influence of Vibration on the Microstructure of the Wear-Resistant Layer Made with the Welding Wire MSG-6-GZ-C-60G -- Research Regarding the Manufacture of Pipelines through Automatic Tandem MAG Welding on Generators -- The Effect of Silicon Content into the Aluminum Matrix on the Microstructure and Mechanical Properties of TIG/FSW Welds; Analyzing Properties of New Hard Coating Technologies for Increasing the Wear Resistance -- Corrective Solutions for the Shaft with Flange Used for Fixing the Blade on a 5 kW Wind Turbine to Withstand Extreme Weather Conditions -- Numerical Modeling and Initial Fatigue Life Estimations of Welded Structural Components -- Reconditioning by Metal Deposition Technology - Temperature Finite Element Modeling -- Lap Joint Laser Welding of Austenitic Stainless Steel Thin Sheets -- Cold Metal Transfer Welding of Aluminum 5456 Thin Sheets -- Study Regarding the Cavitation Erosion Behaviour and Residual Stresses of Impact Resistant Hardfacing Materials -- Refining the Welding Technique for Nuclear Fuel Elements at INR Pitesti -- The Increasing of Corrosion Resistance of Low Alloy Carbon Steels Used in Petroleum Industry through Coating with Alloys Based on Fe-Ni-Cr by Thermal Spray -- Influence of Slag-Flux Mixture on the Properties of Welded Joints -- Analysis of the Quality of the Weld Metal Obtained with Alloyed Flux-Cored Wire -- The Effect of Water Pressure Variation on Cut Surfaces Quality during Abrasive Waterjet Cutting of Austenitic Steels -- Pulsed LASER-(Micro) TIG Welding of Automotive Zn Coated Advanced High Strength Steels Thin Sheets in Overlap Configuration -- Evaluation of Abrasive Wear Resistance of Fe-Cr-C Hardfacing Alloys Deposited on Active Components of the Agricultural Components -- Repair Weld Simulation of Austenitic Steel Pipe -- Joining of C/SiC Materials by Spark Plasma Sintering -- Determination of Some Mechanical Properties of Welded Reinforcing Steel with Self-Shielded Wires by Vibration Tests -- Defects Detection on the Welded Thin Steel Plates Using Vibroacustic Method -- New Ecological Technique for Soldering of Metallic Materials; Research on the Influence of Artificial Ageing on the Tensile Properties of Plastic Coated Composites with Fabric Inserts, in the Presence of Simulated Welding Imperfections -- Keywords Index -- Authors Index N2 - Selected, peer reviewed papers from the 7th International Conference on Innovative Technologies for Joining Advanced Materials (TIMA 14), June 19-20, 2014, Timisoara, Romania UR - https://ebookcentral.proquest.com/lib/orpp/detail.action?docID=1910937 ER -