TY  - BOOK
AU  - Pramujati,Bambang
TI  - Advances in Applied Mechanics and Materials
T2  - Applied Mechanics and Materials Series
SN  - 9783038263715
AV  - TA350 .I58 2013 
PY  - 2014///
CY  - Zurich
PB  - Trans Tech Publications, Limited
KW  - Mechanics, Applied-Congresses
KW  - Electronic books
N1  - Intro -- Advances in Applied Mechanics and Materials -- Editorial Note -- Table of Contents -- Chapter 1: Energy Conversion -- Design of a Bubbling Fluidized Bed Gasifier for the Thermochemical Conversion of Oil Palm Empty Fruit Bunch Briquette -- Laminar Flow Past a Circular Cylinder: Reduction of Drag and Fluctuating Lift Using Upstream and Downstream Rods -- Trans-Esterification of Triglycerides with Methanol on Sulfated Zirconia Prepared with Different Concentration of Sulfuric Acid -- Numerical Studies on R22 Refrigerant Compressor Using Environment Friendly Working Fluids -- Case Studies Thermal Analysis of HP Condensate Stabilizer Column -- The Influence of Hydrogen Addition to Diesel Fuel Spray Combustion for Different Atomization Conditions -- Hydrogen Production from Acetic Acid Steam Reforming over Bimetallic Ni-Co on La2O3 Catalyst-Effect of the Catalyst Dilution -- Driving Efficiency through Hydrocarbon for Green Car Air Conditioning -- Air to Air Ejector with Various Divergent Mixing Chambers -- Kamojang Geothermal Power Plant Unit-1 : 30 Years of Operation -- Flow Visualization Pattern on Sharp Edge T-Junction through Dividing Flow Channel -- An Experimental Study on the Vertical Flow Past a Finite-Length Horizontal Cylinder at Low Reynolds Numbers -- Effect of Air Conditioning Position on Thermal Comfort in the Floor Air Conditioning System -- Computational Fluid Dynamic Using Parallel Loop of Multi-Cores Processor -- Experimental Studies on a Solar Air Heater Having V-Corrugated Absorber Plate with Obstacles Bent Vertically -- Energy Savings in Air Conditioning System Using Ejector: An Overview -- Empirical Correlations for Sizing Adiabatic Capillary Tube Using LPG as Refrigerant in Split-Type Air-Conditioner -- Validation of AWTSim as Aerodynamic Analysis for Design Wind Turbine Blade; Numerical Study on the Influence of the Corner Curvature of Circular Micropillar on Microdroplet Size via a Dewetting Process -- Redesign ITS Central Library through Smart Building -- Optimization of Maximum Lift to Drag Ratio on Airfoil Design Based on Artificial Neural Network Utilizing Genetic Algorithm -- Carbon Dioxide Effects on the Flammability Characteristics of Biogas -- Heat Transfer Effectiveness and Coefficient of Pressure Drop on the Shell Side of a Staggered Elliptical Tubes Bank -- Experimental Study on the Effect of Reynolds Number Variation on Drag Force for Various Cut Angle on D-Type Cylinders -- Performance of Conical Diffuser on Liquid Jet Gas Ejector -- An Investigation into the Effect of Drag Coefficient on Overtaking of Car -- Effects of Pine Oil on Dynamics of Bubble in Froth Flotation -- Study on Auto-Ignition Behavior of Lubricating Oil in a Cone Calorimeter -- Solar Driven Absorption Chiller for Medium Temperature Food Refrigeration, a Study for Application in Indonesia -- The Effect of Water Droplet Size on the Extinguished Concentric Jet Premixed and Diffusion Flame -- Gaining the Enthalpy of Solid Yields Formation in the Process of Waste Pyrolysis -- Pipeline Leak Detection in Two Phase Flow Based on Fluctuation Pressure Difference and Artificial Neural Network (ANN) -- Reduction of Drag Force on a Circular Cylinder and Pressure Drop Using a Square Cylinder as Disturbance Body in a Narrow Channel -- Experimental Study of Drag Reduction on Circular Cylinder and Reduction of Pressure Drop in Narrow Channels by Using a Cylinder Disturbance Body -- Flammability Limit and Flame Visualization of Gaseous Fuel Combustion Inside Meso-scale Combustor with Different Thermal Conductivity -- Energy Conversion in Compliance of Energy Self-Sufficient Village Program. Case Study: Jarak Village; Parallel Speed-Up of Preconditioned Fractional Step Navier-Stokes Solvers -- Reactive Mixing Behavior of the Nitration of Glycerin in a Stirred Vessel at Various Perturbation -- Thermodynamic Analysis of Ejector as an Expansion Device on Split-Type Air Conditioner Using R410A as Working Fluid -- Experimental Investigation on the Use of Secondary Refrigerant in Freezer for Energy Savings -- Investigation of Natural Gas Composition Effects on Knock Phenomenon in SI Gas Engines Using Detailed Chemistry -- Flow Characteristics around Four Circular Cylinders in Equispaced Arrangement near a Plane Wall -- Experimental Study on the Performance of In-Cabin Ventilation System -- Reduction of Energy Losses in the End Wall Junction Area through the Addition of Forward Facing Step Turbulent Generator -- Biogas Potential of Co-Substrates in Balinese Biogas Plants -- CFD Simulation of Heat Transfer in Fluidized Bed Reactor -- Influence of Bioethanol-Gasoline Blended Fuel on Performance and Emissions Characteristics from Port Injection Sinjai Engine 650 cc -- Improved Energy Saving for R22 Building Air Conditioning Retrofitted with Hydrocarbon Refrigerant, Study Case: Civil Engineering Department of ITS -- The Evaluation of a Rigid Sail of Ship Using Wind Tunnel Test -- High-Efficiency Shrouded Micro Wind Turbine for Urban-Built Environment -- Production of Ethanol as a Renewable Energy by Extractive Fermentation -- Kerosene-Water Flow Pattern in T-Junction Vertical Diameter Ratio 0.5 (Variation of Inclination Branch) -- Chapter 2: Mechanical Design -- Modeling and Analysis of Hybrid Shock Absorber for Military Vehicle Suspension -- Design Online Artificial Gain Updating Sliding Mode Algorithm: Applied to Internal Combustion Engine -- Optimization Spring Coil Design for Orthodontic Tooth Movement; Thermal Stress Intensity Factors of Crack in Solid Oxide Fuel Cells -- Intelligent Bearing Diagnostics Using Wavelet Support Vector Machine -- Degradation Trend Estimation and Prognosis of Large Low Speed Slewing Bearing Lifetime -- Electrical Energy from Vibration of a Washing Machine -- Computer Assisted Fracture Reduction and Fixation Simulation for Pelvic Fractures -- Structural Analysis of a Tracking Photovoltaic System with a Pedestal Solar Tracker -- New Polyhedral Elements Based on Virtual Node Method for Solid Mechanics and Heat Transfer Applications -- Experimental Study of Vibration of Prototype Auditory Membrane -- Interaction between a Crack and an Isotropic Tri-Material Media in Anti-Plane Elasticity -- Split Bar Hopkinson with Springs Striker Bar Launcher -- Neural Network-Based Engine Propeller Matching (NN-EPM) for Trimaran Patrol Ship -- Modeling, Prototyping and Testing of Regenerative Electromagnetic Shock Absorber -- Designing and Prototyping Surveillance Robot with Self-Protection Using Nail Gun -- Numerical Modelling of the Initial Stress and Upward Deflection of Glulam Beams Pre-Stresseed by Compressed Wood -- Modular System for Testing the Performance of Poly-Articulate Robotic Structures -- Preliminary Numerical Study on Designing Navigation and Stability Control Systems for ITS AUV -- Numerical Study of Salat Movements for Total Hip Replacement Patient -- Physiological Concept: Visible Modeling for Feasible Design -- Actuator Power Consumption of Active Suspension System with Override Control Strategy -- Trailing Edge Deformation Mechanism for Active Variable - Camber Wind Turbine Blade -- Chapter 3:  Manufacturing Processes and Technologies -- Effect of Material and Process Parameter on Dimensions of Rolled External Threads -- The Emergy Value Assessment of Municipal Waste Management in Yogyakarta, Indonesia; Evaluation of the Effect of Application of Air Jet Cooling and Cooled-Air Jet Cooling on Machining Characteristics of St 60 Steel -- Simulation of Semi-Active the Blank Holder Force Control to Prevent Wrinkling and Cracking in Deep Drawing Process -- System Architecture and FPGA Embedding of Compact Fuzzy Logic Controller for Arm Robot Joints -- Organizational Culture in Manufacturing Company: Study Case of Small and Medium Sized Enterprises in Central Java, Indonesia -- Development Machining of Titanium Alloys: A Review -- Modal and Harmonic Response Analysis: Linear-Approach Simulation to Predict the Influence of Granular Stiffeners on Dynamic Stiffness of Box-Shaped Workpiece for Increasing Stability Limit against Chatter -- The Preliminary Research of Drill Guide Template Design for Pedicle Screw Placement with a Low-Cost 3D Pinter -- Experimental-Based TGPID Motion Control for 2D CNC Machine -- Preliminary Study on Magnetic Levitation Modeling Using PID Control -- Multiple Performance Optimization in the Wire EDM Process of SKD61 Tool Steel Using Taguchi Grey Relational Analysis and Fuzzy Logic -- Optimization of Recast Layer Thickness and Surface Roughness in the Wire EDM Process of AISI H13 Tool Steel Using Taguchi and Fuzzy Logic -- Optimization of Tool Wear, Surface Roughness and Material Removal Rate in the Milling Process of Al 6061 Using Taguchi and Weighted Principal Component Analysis (WPCA) -- Design and Application of the Stretching Technology on the Welding Process of Stiffened Sheet Metal Structure -- Effect of High Speed Dry End Milling on Surface Roughness and Cutting Forces of Ti-6Al-4V ELI -- Visible Light Maskless Photolithography for Biomachining Application -- Improvement of Tungsten Inert Gas (TIG) Welding Penetration Using the Effect of Electromagnetic Field; Response of Grip Force as Effect of Electrics Power Input at Gripper Actuator of NiTi SM495 Wire
N2  - Selected, peer reviewed papers from the International Conference on Mechanical Engineering (ICOME 2013), September 19-21, 2013, Mataram, Lombok, Indonesia
UR  - https://ebookcentral.proquest.com/lib/orpp/detail.action?docID=1910691
ER  -