Advances in Applied Mechanics and Materials.
- 1st ed.
- 1 online resource (800 pages)
- Applied Mechanics and Materials Series ; v.Volume 493 .
- Applied Mechanics and Materials Series .
Intro -- Advances in Applied Mechanics and Materials -- Editorial Note -- Table of Contents -- Chapter 1: Energy Conversion -- Design of a Bubbling Fluidized Bed Gasifier for the Thermochemical Conversion of Oil Palm Empty Fruit Bunch Briquette -- Laminar Flow Past a Circular Cylinder: Reduction of Drag and Fluctuating Lift Using Upstream and Downstream Rods -- Trans-Esterification of Triglycerides with Methanol on Sulfated Zirconia Prepared with Different Concentration of Sulfuric Acid -- Numerical Studies on R22 Refrigerant Compressor Using Environment Friendly Working Fluids -- Case Studies Thermal Analysis of HP Condensate Stabilizer Column -- The Influence of Hydrogen Addition to Diesel Fuel Spray Combustion for Different Atomization Conditions -- Hydrogen Production from Acetic Acid Steam Reforming over Bimetallic Ni-Co on La2O3 Catalyst-Effect of the Catalyst Dilution -- Driving Efficiency through Hydrocarbon for Green Car Air Conditioning -- Air to Air Ejector with Various Divergent Mixing Chambers -- Kamojang Geothermal Power Plant Unit-1 : 30 Years of Operation -- Flow Visualization Pattern on Sharp Edge T-Junction through Dividing Flow Channel -- An Experimental Study on the Vertical Flow Past a Finite-Length Horizontal Cylinder at Low Reynolds Numbers -- Effect of Air Conditioning Position on Thermal Comfort in the Floor Air Conditioning System -- Computational Fluid Dynamic Using Parallel Loop of Multi-Cores Processor -- Experimental Studies on a Solar Air Heater Having V-Corrugated Absorber Plate with Obstacles Bent Vertically -- Energy Savings in Air Conditioning System Using Ejector: An Overview -- Empirical Correlations for Sizing Adiabatic Capillary Tube Using LPG as Refrigerant in Split-Type Air-Conditioner -- Validation of AWTSim as Aerodynamic Analysis for Design Wind Turbine Blade. Numerical Study on the Influence of the Corner Curvature of Circular Micropillar on Microdroplet Size via a Dewetting Process -- Redesign ITS Central Library through Smart Building -- Optimization of Maximum Lift to Drag Ratio on Airfoil Design Based on Artificial Neural Network Utilizing Genetic Algorithm -- Carbon Dioxide Effects on the Flammability Characteristics of Biogas -- Heat Transfer Effectiveness and Coefficient of Pressure Drop on the Shell Side of a Staggered Elliptical Tubes Bank -- Experimental Study on the Effect of Reynolds Number Variation on Drag Force for Various Cut Angle on D-Type Cylinders -- Performance of Conical Diffuser on Liquid Jet Gas Ejector -- An Investigation into the Effect of Drag Coefficient on Overtaking of Car -- Effects of Pine Oil on Dynamics of Bubble in Froth Flotation -- Study on Auto-Ignition Behavior of Lubricating Oil in a Cone Calorimeter -- Solar Driven Absorption Chiller for Medium Temperature Food Refrigeration, a Study for Application in Indonesia -- The Effect of Water Droplet Size on the Extinguished Concentric Jet Premixed and Diffusion Flame -- Gaining the Enthalpy of Solid Yields Formation in the Process of Waste Pyrolysis -- Pipeline Leak Detection in Two Phase Flow Based on Fluctuation Pressure Difference and Artificial Neural Network (ANN) -- Reduction of Drag Force on a Circular Cylinder and Pressure Drop Using a Square Cylinder as Disturbance Body in a Narrow Channel -- Experimental Study of Drag Reduction on Circular Cylinder and Reduction of Pressure Drop in Narrow Channels by Using a Cylinder Disturbance Body -- Flammability Limit and Flame Visualization of Gaseous Fuel Combustion Inside Meso-scale Combustor with Different Thermal Conductivity -- Energy Conversion in Compliance of Energy Self-Sufficient Village Program. Case Study: Jarak Village. Parallel Speed-Up of Preconditioned Fractional Step Navier-Stokes Solvers -- Reactive Mixing Behavior of the Nitration of Glycerin in a Stirred Vessel at Various Perturbation -- Thermodynamic Analysis of Ejector as an Expansion Device on Split-Type Air Conditioner Using R410A as Working Fluid -- Experimental Investigation on the Use of Secondary Refrigerant in Freezer for Energy Savings -- Investigation of Natural Gas Composition Effects on Knock Phenomenon in SI Gas Engines Using Detailed Chemistry -- Flow Characteristics around Four Circular Cylinders in Equispaced Arrangement near a Plane Wall -- Experimental Study on the Performance of In-Cabin Ventilation System -- Reduction of Energy Losses in the End Wall Junction Area through the Addition of Forward Facing Step Turbulent Generator -- Biogas Potential of Co-Substrates in Balinese Biogas Plants -- CFD Simulation of Heat Transfer in Fluidized Bed Reactor -- Influence of Bioethanol-Gasoline Blended Fuel on Performance and Emissions Characteristics from Port Injection Sinjai Engine 650 cc -- Improved Energy Saving for R22 Building Air Conditioning Retrofitted with Hydrocarbon Refrigerant, Study Case: Civil Engineering Department of ITS -- The Evaluation of a Rigid Sail of Ship Using Wind Tunnel Test -- High-Efficiency Shrouded Micro Wind Turbine for Urban-Built Environment -- Production of Ethanol as a Renewable Energy by Extractive Fermentation -- Kerosene-Water Flow Pattern in T-Junction Vertical Diameter Ratio 0.5 (Variation of Inclination Branch) -- Chapter 2: Mechanical Design -- Modeling and Analysis of Hybrid Shock Absorber for Military Vehicle Suspension -- Design Online Artificial Gain Updating Sliding Mode Algorithm: Applied to Internal Combustion Engine -- Optimization Spring Coil Design for Orthodontic Tooth Movement. Thermal Stress Intensity Factors of Crack in Solid Oxide Fuel Cells -- Intelligent Bearing Diagnostics Using Wavelet Support Vector Machine -- Degradation Trend Estimation and Prognosis of Large Low Speed Slewing Bearing Lifetime -- Electrical Energy from Vibration of a Washing Machine -- Computer Assisted Fracture Reduction and Fixation Simulation for Pelvic Fractures -- Structural Analysis of a Tracking Photovoltaic System with a Pedestal Solar Tracker -- New Polyhedral Elements Based on Virtual Node Method for Solid Mechanics and Heat Transfer Applications -- Experimental Study of Vibration of Prototype Auditory Membrane -- Interaction between a Crack and an Isotropic Tri-Material Media in Anti-Plane Elasticity -- Split Bar Hopkinson with Springs Striker Bar Launcher -- Neural Network-Based Engine Propeller Matching (NN-EPM) for Trimaran Patrol Ship -- Modeling, Prototyping and Testing of Regenerative Electromagnetic Shock Absorber -- Designing and Prototyping Surveillance Robot with Self-Protection Using Nail Gun -- Numerical Modelling of the Initial Stress and Upward Deflection of Glulam Beams Pre-Stresseed by Compressed Wood -- Modular System for Testing the Performance of Poly-Articulate Robotic Structures -- Preliminary Numerical Study on Designing Navigation and Stability Control Systems for ITS AUV -- Numerical Study of Salat Movements for Total Hip Replacement Patient -- Physiological Concept: Visible Modeling for Feasible Design -- Actuator Power Consumption of Active Suspension System with Override Control Strategy -- Trailing Edge Deformation Mechanism for Active Variable - Camber Wind Turbine Blade -- Chapter 3: Manufacturing Processes and Technologies -- Effect of Material and Process Parameter on Dimensions of Rolled External Threads -- The Emergy Value Assessment of Municipal Waste Management in Yogyakarta, Indonesia. Evaluation of the Effect of Application of Air Jet Cooling and Cooled-Air Jet Cooling on Machining Characteristics of St 60 Steel -- Simulation of Semi-Active the Blank Holder Force Control to Prevent Wrinkling and Cracking in Deep Drawing Process -- System Architecture and FPGA Embedding of Compact Fuzzy Logic Controller for Arm Robot Joints -- Organizational Culture in Manufacturing Company: Study Case of Small and Medium Sized Enterprises in Central Java, Indonesia -- Development Machining of Titanium Alloys: A Review -- Modal and Harmonic Response Analysis: Linear-Approach Simulation to Predict the Influence of Granular Stiffeners on Dynamic Stiffness of Box-Shaped Workpiece for Increasing Stability Limit against Chatter -- The Preliminary Research of Drill Guide Template Design for Pedicle Screw Placement with a Low-Cost 3D Pinter -- Experimental-Based TGPID Motion Control for 2D CNC Machine -- Preliminary Study on Magnetic Levitation Modeling Using PID Control -- Multiple Performance Optimization in the Wire EDM Process of SKD61 Tool Steel Using Taguchi Grey Relational Analysis and Fuzzy Logic -- Optimization of Recast Layer Thickness and Surface Roughness in the Wire EDM Process of AISI H13 Tool Steel Using Taguchi and Fuzzy Logic -- Optimization of Tool Wear, Surface Roughness and Material Removal Rate in the Milling Process of Al 6061 Using Taguchi and Weighted Principal Component Analysis (WPCA) -- Design and Application of the Stretching Technology on the Welding Process of Stiffened Sheet Metal Structure -- Effect of High Speed Dry End Milling on Surface Roughness and Cutting Forces of Ti-6Al-4V ELI -- Visible Light Maskless Photolithography for Biomachining Application -- Improvement of Tungsten Inert Gas (TIG) Welding Penetration Using the Effect of Electromagnetic Field. Response of Grip Force as Effect of Electrics Power Input at Gripper Actuator of NiTi SM495 Wire.
Selected, peer reviewed papers from the International Conference on Mechanical Engineering (ICOME 2013), September 19-21, 2013, Mataram, Lombok, Indonesia.