Current Development of Mechanical Engineering and Energy.
Shao, J. X.
Current Development of Mechanical Engineering and Energy. - 1st ed. - 1 online resource (1950 pages) - Applied Mechanics and Materials Series ; v.Volumes 494-495 . - Applied Mechanics and Materials Series .
Intro -- Current Development of Mechanical Engineering and Energy -- Preface -- Table of Contents -- Chapter 1: Vehicle and Transportation Engineering -- Study on the Larger Bus Body Stability of Bend Steering -- Study on Photovoltaic Array Design for Solar Energy Vehicle -- Study of a New Type of Dangerous Goods Transport Vehicle Rear Protective Device -- An In-Vehicle Monitoring System with OBD-Based Vehicle Terminal -- Research on Electric Vehicle Charging & -- Battery Swapping Robot System -- Modeling and Simulation of MacPherson Suspension Based on LMS Virtual.Lab Motion -- Design of Power Windows Based on POWERLINK Industrial Ethernet -- The Summarize of High Power LED Headlamps Cooling Design of Automobile -- Design Calculation on Chain Conveyor of Material Storage and Transportation Box of Automatic Loading and Unloading Vehicle -- A Study on Brake Noise Using the Complex Modal Analysis Method -- Comfort Evaluation Research on Clutch Operation of Light Commercial Vehicle -- Research on Integration Design of Automobile Waste Heat Thermoelectric Generation Exchanger and Engine Muffler -- Simulation and Study on Ride Comfort of Articulated Dump Truck Based on Rigid-Flex Coupling -- The Hall Automotive Wheel Speed Sensor and Simulation for its Signal Processing -- Wind-Induced Vibration of the Rear-View Mirrors of Car at High Speed -- Research on the Affection of Vehicle Lateral Stability Related to the Improved ABS -- The Quantification Research of Engine Body Defect that Tested by Ultrasonic Phased Array -- Analysis of Vehicle Interior Low-Frequency Noise Based on ATV -- The Engine Oil Sump Radiated Noise Optimization Design -- A Novel OFDM Radar Algorithm in Vehicular Environment -- Kinetic Analysis of the Unbalanced Masses of Wheel Based on ADAMS -- Study on the Fuel-Saving Efficiency of Electric Vehicles under Empirical Test. Thermal Management System Design and Simulation of Battery Pack for Electric Vehicles -- Vehicle Embedded Speech Recognition and Control System Research and Implementation -- A Comparative Study on Driving Performance Induced by Music Mood for Development of In-Vehicle Media Players -- Analysis of Automotive Steering Column Regulation Performance Based on Abaqus -- Vehicle Suspension K& -- C Characteristic Simulation Analysis Based on ADAMS -- Design of System to Prevent Drunken Driving Based on Internet of Vehicles -- Achieve the WWD-0.8/10 Air Compressor's Motion Simulation -- The Ergonomics Research of the Joystick in Excavator Cab -- Research on the Split Electric Variable Transmission for Hybrid Electric Vehicle -- Simulation Research on Aerodynamic Characteristics of Vehicle under Steady Crosswind Based on XFlow -- Vibration Fatigue Analysis for the Frame of Vehicle Equipment -- Analysis and Simulation System of Vehicle Dynamic Performance -- Research on the Effect of Alignments of Mountainous Highways on Driver Characteristics -- Conjoint Simulation of Active Suspension and ABS -- Integrated Design for Steering System and Suspension -- Modeling of Interlinked Air Suspension and Study on its Dynamic Performance -- Characteristics of the Hydro-Mechanical Continuously Variable Transmission in the Wheeled Tractor -- Research of Pure Tone Detection for Faulted On-Vehicle Loudspeakers Based on Image Fractal -- Research on Hydraulic Response Characteristics of Inlet Valve Used in Hydraulic Braking System -- Simulation Research of Hydraulic Powerplant Mount Based on Matlab/Simulink -- Design and Research of Engine Electronic Fuel Injection Simulation Experimental Platform -- Structural Analysis of a Tractor Chassis via FEM -- Research on the Evaluation of China's Automotive Industry Security: Based on Gray Model. Study on the Dynamic Characteristics of Hot-Film Flow Sensor Based on the Sampling Air Channel -- 1-D Simulation of a Diesel Engines Injection Timing -- Design and Implement of the Car Reversing Automatic Anti-Collision Control System -- Technology of Vehicle Detail Parts Monitoring Based on CGI and IPv6 -- Analysis of Influence Factors on Braking Energy Recovery of Pure Electric Vehicle -- Optimal Torque Distribution Strategy of Hybrid Electric Bus Based on Genetic Algorithms -- Design of Control System of Eddy Current Retarder Based on BP Neural Network PID Controller -- Dynamic Modeling and Simulation on a Hybrid Power System for Dual-Motor-Drive Electric Tracked Bulldozer -- The Virtual Simulation of Electric-Drive Mechanical Transmission -- Study of Electric Vehicle Lithium Batteries -- Electronic Control Unit Design of Electronically Controlled Air Suspension (ECAS) for Vehicle Based on Freescale Microcontroller -- Modeling and Simulation Research on Lithium-Ion Battery in Electric Vehicles Based on Genetic Algorithm -- Analysis and Design of Information Management System for Defective Automobile Products Recall -- High Voltage Safety Management System Design Based on Functional Safety -- The Forming Process Simulation of Magnesium Alloy Control Arm of Automobile and its Mold Design -- The Study of Automatically Leveling Control System on Electromechanical Vehicle Stable Platform -- Chapter 2: Design and Manufacturing Technology in Mechanical Engineering -- Lifting Platform Hinge Shaft Contact Finite Element Analysis -- Finite Element Analysis of Material Mechanics Experiment -- Design and Implementation of the Disassembly and Assembly Equipment to the Buffer Braking Device of the Elevating Mechanism of the Heavy Caliber Ground Artillery -- The Experimental Study on the Enhanced Evaporating Property of the Pineapple Juice by Ultrasound. Research on Temperature Distribution and Stress Distribution Model of Prefabricate Block Electric Furnace Roof -- Study of a Four Rotor Aircraft Modeling -- Preliminary Exploration of the Dynamic Model and Experiment on an Impact between a Tennis Ball and Racket -- Sports Biomechanical Research and Exploration on the Tennis Injuries -- Structure Optimization of Agricultural Vehicle Frame Based on APDL -- Analysis of Air-Flow Field of Large Ships in Waves -- Flow Field Analysis of HVAC Face-Blowing Duct Based on CFD -- A Study on Preparation Process Experiment of a Large Diameter Cylinder with High Precision -- Force Analysis of the Anchor Chains and the Cable in the Crane-System with a Floating Base in Regular Waves -- Preliminary Analysis on Precision Control of Reverse Retrofit Design of the Product -- Research of Shell PTDF Shrink Model -- Design and Strength Analysis of the Wheelchair Switching Mechanism -- Design and Dynamic Deformation Analysis for Elastic Cutter Fixture of Tool Grasper Mechanism on Disc Type Tool Magazine with Double Loop Cutters -- The Finite Element Analysis of the Stress and Deformation of the Micro-Milling Cutter Based on ANSYS -- Deformation Analysis of Stator of Opposed Biconinal Cone Screw Seawater Hydraulic Pump -- Reliability and Failure Analysis of CNC Machine Based on Element Action -- The Research on Computer Aided Design Combined with Product Design -- Research of Gantry Machining Center Assembly Deviation Sensitivity Based on Multi-Body System -- Bolt Static Finite Element Numerical Simulation and Experimental Research -- Research on the Influence of Hot Strip Shape to Ribbing Defect -- Finite Element Study of Ultrasonic Elliptical Vibration Turning of Ti6Al4V -- Model Development for a Composite Core-Pulling Mechanism. The Effect of Droplet Impingement on Pressure and Heat Flux Distributions on Molten Pool in GMAW-Based Rapid Forming -- Study on Damage Ability of Anti-Armor Composite Warhead -- The Study on the Nanocutting by Rigid Body Tool at the Gas Environment Using Molecular Dynamics Simulations -- Topology Optimization of the Base of Loading Device -- Research on Operational Reliability Index of Centrifugal Pump -- Primary Research on Processing Method of Elliptic Workpieces -- Mechanical Structure Design of the Full-Automatic Coil Strapping Machine -- Numerical Simulation of Thrust Vector Control for a 2D Nozzle -- Study on the Positive EDM Based on the Field Emission Theory -- Study on the Hole-Wedge Effect of Friction Pair -- Test Analysis of the 60 Tons Converter -- The Research of Fuel Pressure Fluctuations within Diesel Injection Pump Cavity on Cam Shaft Rotate Speed -- The Optimized Analysis of Ladder Structure of the Aerial Ladder Truck -- Dynamic Propagation Problems of Symmetrical Mode III Crack -- The Study on 5-DOF CNC Machine Tool Motion -- Mold Design for a Composite Core-Pulling Mechanism -- The Strain Analysis at the Broadening Stage of the Hollow Railway Axle by Multi-Wedge Cross Wedge Rolling -- Research on Process Parameter Optimization of the High-Neck Flange Closed Rolling Based on the Orthogonal Experimental Design -- Investigation on the Sheet Metal Anisotropy by the Plane Strain Compression Method with Laminated Samples -- Analysis of Chair's Materials and the Wooden Chair Manufacturing Process -- The Development of Tribology -- The Statics Analysis of the Lathe Tool Based on Workbench -- An FTPBM Model for Conceptual Design of Mechanical Execution System -- Study on Compacting Mechanism of Plate Cross Wedge Rolling High-Speed Rail Screw Spike -- Recent Study on the Passive and Active Vibration Isolators. Comparison of the Geometric Accuracy by DSIF Toolpath with SPIF Toolpath.
Selected, peer reviewed papers from the 2013 International Symposium on Vehicle, Mechanical, and Electrical Engineering (ISVMEE 2013), December 21-22, 2013, Taiwan, China.
9783038263845
Motor vehicles-Design and construction-Congresses.
Automobiles-Design and construction-Congresses.
Electrical engineering-Congresses.
Mechanical engineering-Congresses.
Electronic books.
TL240 .I58 2013
Current Development of Mechanical Engineering and Energy. - 1st ed. - 1 online resource (1950 pages) - Applied Mechanics and Materials Series ; v.Volumes 494-495 . - Applied Mechanics and Materials Series .
Intro -- Current Development of Mechanical Engineering and Energy -- Preface -- Table of Contents -- Chapter 1: Vehicle and Transportation Engineering -- Study on the Larger Bus Body Stability of Bend Steering -- Study on Photovoltaic Array Design for Solar Energy Vehicle -- Study of a New Type of Dangerous Goods Transport Vehicle Rear Protective Device -- An In-Vehicle Monitoring System with OBD-Based Vehicle Terminal -- Research on Electric Vehicle Charging & -- Battery Swapping Robot System -- Modeling and Simulation of MacPherson Suspension Based on LMS Virtual.Lab Motion -- Design of Power Windows Based on POWERLINK Industrial Ethernet -- The Summarize of High Power LED Headlamps Cooling Design of Automobile -- Design Calculation on Chain Conveyor of Material Storage and Transportation Box of Automatic Loading and Unloading Vehicle -- A Study on Brake Noise Using the Complex Modal Analysis Method -- Comfort Evaluation Research on Clutch Operation of Light Commercial Vehicle -- Research on Integration Design of Automobile Waste Heat Thermoelectric Generation Exchanger and Engine Muffler -- Simulation and Study on Ride Comfort of Articulated Dump Truck Based on Rigid-Flex Coupling -- The Hall Automotive Wheel Speed Sensor and Simulation for its Signal Processing -- Wind-Induced Vibration of the Rear-View Mirrors of Car at High Speed -- Research on the Affection of Vehicle Lateral Stability Related to the Improved ABS -- The Quantification Research of Engine Body Defect that Tested by Ultrasonic Phased Array -- Analysis of Vehicle Interior Low-Frequency Noise Based on ATV -- The Engine Oil Sump Radiated Noise Optimization Design -- A Novel OFDM Radar Algorithm in Vehicular Environment -- Kinetic Analysis of the Unbalanced Masses of Wheel Based on ADAMS -- Study on the Fuel-Saving Efficiency of Electric Vehicles under Empirical Test. Thermal Management System Design and Simulation of Battery Pack for Electric Vehicles -- Vehicle Embedded Speech Recognition and Control System Research and Implementation -- A Comparative Study on Driving Performance Induced by Music Mood for Development of In-Vehicle Media Players -- Analysis of Automotive Steering Column Regulation Performance Based on Abaqus -- Vehicle Suspension K& -- C Characteristic Simulation Analysis Based on ADAMS -- Design of System to Prevent Drunken Driving Based on Internet of Vehicles -- Achieve the WWD-0.8/10 Air Compressor's Motion Simulation -- The Ergonomics Research of the Joystick in Excavator Cab -- Research on the Split Electric Variable Transmission for Hybrid Electric Vehicle -- Simulation Research on Aerodynamic Characteristics of Vehicle under Steady Crosswind Based on XFlow -- Vibration Fatigue Analysis for the Frame of Vehicle Equipment -- Analysis and Simulation System of Vehicle Dynamic Performance -- Research on the Effect of Alignments of Mountainous Highways on Driver Characteristics -- Conjoint Simulation of Active Suspension and ABS -- Integrated Design for Steering System and Suspension -- Modeling of Interlinked Air Suspension and Study on its Dynamic Performance -- Characteristics of the Hydro-Mechanical Continuously Variable Transmission in the Wheeled Tractor -- Research of Pure Tone Detection for Faulted On-Vehicle Loudspeakers Based on Image Fractal -- Research on Hydraulic Response Characteristics of Inlet Valve Used in Hydraulic Braking System -- Simulation Research of Hydraulic Powerplant Mount Based on Matlab/Simulink -- Design and Research of Engine Electronic Fuel Injection Simulation Experimental Platform -- Structural Analysis of a Tractor Chassis via FEM -- Research on the Evaluation of China's Automotive Industry Security: Based on Gray Model. Study on the Dynamic Characteristics of Hot-Film Flow Sensor Based on the Sampling Air Channel -- 1-D Simulation of a Diesel Engines Injection Timing -- Design and Implement of the Car Reversing Automatic Anti-Collision Control System -- Technology of Vehicle Detail Parts Monitoring Based on CGI and IPv6 -- Analysis of Influence Factors on Braking Energy Recovery of Pure Electric Vehicle -- Optimal Torque Distribution Strategy of Hybrid Electric Bus Based on Genetic Algorithms -- Design of Control System of Eddy Current Retarder Based on BP Neural Network PID Controller -- Dynamic Modeling and Simulation on a Hybrid Power System for Dual-Motor-Drive Electric Tracked Bulldozer -- The Virtual Simulation of Electric-Drive Mechanical Transmission -- Study of Electric Vehicle Lithium Batteries -- Electronic Control Unit Design of Electronically Controlled Air Suspension (ECAS) for Vehicle Based on Freescale Microcontroller -- Modeling and Simulation Research on Lithium-Ion Battery in Electric Vehicles Based on Genetic Algorithm -- Analysis and Design of Information Management System for Defective Automobile Products Recall -- High Voltage Safety Management System Design Based on Functional Safety -- The Forming Process Simulation of Magnesium Alloy Control Arm of Automobile and its Mold Design -- The Study of Automatically Leveling Control System on Electromechanical Vehicle Stable Platform -- Chapter 2: Design and Manufacturing Technology in Mechanical Engineering -- Lifting Platform Hinge Shaft Contact Finite Element Analysis -- Finite Element Analysis of Material Mechanics Experiment -- Design and Implementation of the Disassembly and Assembly Equipment to the Buffer Braking Device of the Elevating Mechanism of the Heavy Caliber Ground Artillery -- The Experimental Study on the Enhanced Evaporating Property of the Pineapple Juice by Ultrasound. Research on Temperature Distribution and Stress Distribution Model of Prefabricate Block Electric Furnace Roof -- Study of a Four Rotor Aircraft Modeling -- Preliminary Exploration of the Dynamic Model and Experiment on an Impact between a Tennis Ball and Racket -- Sports Biomechanical Research and Exploration on the Tennis Injuries -- Structure Optimization of Agricultural Vehicle Frame Based on APDL -- Analysis of Air-Flow Field of Large Ships in Waves -- Flow Field Analysis of HVAC Face-Blowing Duct Based on CFD -- A Study on Preparation Process Experiment of a Large Diameter Cylinder with High Precision -- Force Analysis of the Anchor Chains and the Cable in the Crane-System with a Floating Base in Regular Waves -- Preliminary Analysis on Precision Control of Reverse Retrofit Design of the Product -- Research of Shell PTDF Shrink Model -- Design and Strength Analysis of the Wheelchair Switching Mechanism -- Design and Dynamic Deformation Analysis for Elastic Cutter Fixture of Tool Grasper Mechanism on Disc Type Tool Magazine with Double Loop Cutters -- The Finite Element Analysis of the Stress and Deformation of the Micro-Milling Cutter Based on ANSYS -- Deformation Analysis of Stator of Opposed Biconinal Cone Screw Seawater Hydraulic Pump -- Reliability and Failure Analysis of CNC Machine Based on Element Action -- The Research on Computer Aided Design Combined with Product Design -- Research of Gantry Machining Center Assembly Deviation Sensitivity Based on Multi-Body System -- Bolt Static Finite Element Numerical Simulation and Experimental Research -- Research on the Influence of Hot Strip Shape to Ribbing Defect -- Finite Element Study of Ultrasonic Elliptical Vibration Turning of Ti6Al4V -- Model Development for a Composite Core-Pulling Mechanism. The Effect of Droplet Impingement on Pressure and Heat Flux Distributions on Molten Pool in GMAW-Based Rapid Forming -- Study on Damage Ability of Anti-Armor Composite Warhead -- The Study on the Nanocutting by Rigid Body Tool at the Gas Environment Using Molecular Dynamics Simulations -- Topology Optimization of the Base of Loading Device -- Research on Operational Reliability Index of Centrifugal Pump -- Primary Research on Processing Method of Elliptic Workpieces -- Mechanical Structure Design of the Full-Automatic Coil Strapping Machine -- Numerical Simulation of Thrust Vector Control for a 2D Nozzle -- Study on the Positive EDM Based on the Field Emission Theory -- Study on the Hole-Wedge Effect of Friction Pair -- Test Analysis of the 60 Tons Converter -- The Research of Fuel Pressure Fluctuations within Diesel Injection Pump Cavity on Cam Shaft Rotate Speed -- The Optimized Analysis of Ladder Structure of the Aerial Ladder Truck -- Dynamic Propagation Problems of Symmetrical Mode III Crack -- The Study on 5-DOF CNC Machine Tool Motion -- Mold Design for a Composite Core-Pulling Mechanism -- The Strain Analysis at the Broadening Stage of the Hollow Railway Axle by Multi-Wedge Cross Wedge Rolling -- Research on Process Parameter Optimization of the High-Neck Flange Closed Rolling Based on the Orthogonal Experimental Design -- Investigation on the Sheet Metal Anisotropy by the Plane Strain Compression Method with Laminated Samples -- Analysis of Chair's Materials and the Wooden Chair Manufacturing Process -- The Development of Tribology -- The Statics Analysis of the Lathe Tool Based on Workbench -- An FTPBM Model for Conceptual Design of Mechanical Execution System -- Study on Compacting Mechanism of Plate Cross Wedge Rolling High-Speed Rail Screw Spike -- Recent Study on the Passive and Active Vibration Isolators. Comparison of the Geometric Accuracy by DSIF Toolpath with SPIF Toolpath.
Selected, peer reviewed papers from the 2013 International Symposium on Vehicle, Mechanical, and Electrical Engineering (ISVMEE 2013), December 21-22, 2013, Taiwan, China.
9783038263845
Motor vehicles-Design and construction-Congresses.
Automobiles-Design and construction-Congresses.
Electrical engineering-Congresses.
Mechanical engineering-Congresses.
Electronic books.
TL240 .I58 2013