Mechatronics and Applied Mechanics III.

Intro -- Mechatronics and Applied Mechanics III -- Preface, Committees and Sponsors -- Table of Contents -- Chapter 1: Mechatronics -- Design of a 6-DOF VCM-Driven Micro Stage -- Embedded PLC Programming Techniques of Forging CNC System -- Preliminary Study on Piezoelectric Actuation Solution Proportioner -- Research of Double Nozzle Flapper Valve Accelerated Degradation Test -- Research of Intelligent Mower Based on High Accuracy 3D Electronic Compass -- Modeling and Performance Analysis of Switched Reluctance Motor in Electric Vehicles -- The Sensorless Control of IPMSM Based on the Extended State Sliding Mode Observer -- Study on Nonlinear Backlash of Shipboard Antenna Servo System -- Development of High-Speed Response Electromagnetic Linear Actuator Using for Pneumatic Control Valve -- Study on Linear Active Disturbance Rejection Control Technique and its Application in Ship-Borne Servo Control System -- Model Predictive Control Dedicated to an Electrified Auxiliary in HEV/PHEV -- Adaptive Robust Control for Servo System with Combustion Gas Flow Disturbance and Load Uncertainties -- Design and Implementation of Actuator Controller for Greenhouse Control System -- Modeling and Control for a Small UAV Helicopter -- Adaptive Impedance Control for a Tendon-Sheath-Driven Compliant Gripper -- Chapter 2: Sensors and Measurements -- Nondestructive Technique for the Determination of Cracks Parameters by Eddy Current in Differential Mode -- Research of Shock Wave Damage Evaluation Method Based on LY-12 Effect Plate -- Mechanism Study of Acoustics Method for Dryness Measuring and Model Establishment -- Fault Diagnosis for Rotator in Rotating Machinery Based on Support Vector Machine -- Sampling Strategy for Free-Form Surface Inspection Using Coordinate Measuring Machines.

Diagnosis Rule Discovery Based on Causality in the Context of Fault Diagnosis in Rotating Machinery -- Chapter 3: Processing of Signal and Data -- Positioning Algorithm of Underground Personnel Based on ZigBee Technology -- Method of Image Matching for Seabed Sonar Images Based on Regions of Interest -- Study on the Fundamental of Crop Pest Image Recognition -- A New View of Mode Mixing Phenomenon -- An Algorithm of Digital Image Watermarking Based on Turbo Code and Particle Swarm Optimization -- Research on Demodulation Algorithm of PCM/FM Signal -- Research on Soft Demodulation of Anamorphic PCM/FM Signal under the Condition of Low SNR -- Research on Soft Demodulation of Telemetry Signal Based on the Orthogonal Complex Baseband Rotating MSD -- Research of Noise Reduction Algorithm Based on Real Time -- Chapter 4: Robotics, Automation and Control -- A Monocular Vision Measurement Algorithm Based on the Underwater Robot -- Design of a Remote-Controlled Basketball-Playing Mobile Robot -- Design of Automatic Insertion System for a Tendon-Sheath-Driven Searching and Rescuing Robot -- Application of Photovoltaic Radar Target Simulator by Developing RFID Middleware -- Application Research of Integrated Design Using Reinforcement Learning Model -- Sinusoidal Path Planning for Attitude Maneuver of Flexible Spacecraft -- The Application of the Amorphous Metal Transformers in Heavy Oil Electric Heating System -- Motion Control System and Control Algorithm of 3-Axes Platform Based on Controller Area Network -- The Internal Model Control of Greenhouse System Based on LS_SVM -- Design and Implementation of Intelligent Control System for Infrared Shrink Film Machine -- Automatic Bone Drilling in Orthopedic Surgery Parameter Tuning of an Active Force Control -- Model Reference Adaptive Motion Control Research of Servo Press.

Design of a Tendon-Sheath-Driven Robot with Proportional Control for Medical Surgery -- Chapter 5: Applied Information Technologies and Algorithms -- Application of UML for Embedded System Design -- Image Vectorization Based on Mathematical Morphology in Geographic Information System -- Research and Development of an Embedded Security Network Card Based on AM 1808 -- Research on Virtual Cellular Manufacturing Scheduling Based on the Scale-Free Random Network Model -- Development of an Intelligent CAD System for Involute Cylindrical Gear Cutting Tools -- Research and Application on NURBS Curve Inverse Algorithm -- Research on Construction of Kinect-Based Virtual Situation Laboratory -- Design of General ATS Software Platform Based on Components -- Study and Realization of Three-Dimensional Human Body Modeling -- Chapter 6: Design of Machines and Mechanisms -- A General Inverse Kinematic Analysis of 6-Dof Articulated Manipulators -- A Practical Real-Time Motion Cueing Algorithm for Crane Simulator -- Analysis and Detection of Elastic Deformation of the Large-Scale Crankshaft in Non-Circular Grinding -- Analysis on Nonlinear Buckling Failure Influence Factors of Telescopic Boom System Based on Arc-Length and FEM Method -- Application of Parallel Mechanism in Multi-DIM Vibration Absorbers -- CAE Simulation Study on Thermal Stress of Butterfly Valve and Actuator -- Corrosion Prevention in Boilers by Using Energy Audit Consideration -- Design and Experiment of Thermal Water and Mechanical Deicing Device -- Effects of Flexural Stiffness, Axial Velocity and Internal Support Locations on Translating Beam's Natural Frequencies -- Herringbone Gear Meshing Force Simulation Based on UG and ADAMS -- Modal Testing and Parameters' Identification of Spray Boom.

Numerical Simulation of the Influence of Curvature Radius on Aerodynamic Characteristics of the Moving Vehicle -- Numerical Simulation Study on the Thickness of Cylinder Influencing on Energy-Absorbing Characteristics -- Simulation of Dynamic Crack Propagation under Quasistatic Loading -- Simulation Study on High-Powered Shaped Charge Warhead Penetrating into Target with Water Layer -- Solitary Wave and Periodic Wave Solutions and Chaotic Behaviors in a (2+1)-Dimensional Nonlinear System -- Study on Tube Formation Mechanism and Lateral Stiffness Testing Method of the Tubular Conveyor Belt -- Study of the Solitoff Solution and Fractal Solution for the (2+1)-Dimensional Broek-Kaup System with Variable Coefficients -- The Research of Lean Combustion Characteristic of Compound Injection System of Direct Injection Engine -- Tracking Property Analysis of a Dry Gas Seal Operating in Low Pressure Condition -- Vibration Test and Fault Diagnosis for Main Hoist Gearbox of Heavy Casting Crane -- Statics, Instantaneous Kinematics and Singularity Analysis of Planar Parallel Manipulators via Grassmann-Cayley Algebra -- Research on the Model of Scramjet Fuel Supply System -- Designation and Optimization of an Offset Self-Adaption Centralizer with Three Pairs of Arms -- Optimization of Roadheader Crawler Parameters Based on the Theory of Driving -- Precise Frequency Calculation Model on BTA Boring Bar -- Shallowly Discuss the SUV External Projections Check -- Thermal Fatigue Analysis of HSK Shrink Toolholder -- The Modal and Harmonic Response Analysis of the Oil and Water Separation Process under the Shaft -- Research on Stress Intensity Factor of Wheels with Cracks -- The Optimization Design of Multistage Hybrid Planetary Transmission Based on Improved Genetic Algorithm -- Research of Transferring Characteristics of Ink among Rollers.

Development of a Grinding Carriage for an Inner Cooling Grinding in a General Grinding Machine -- Heat Transfer Analysis of Exhaust Manifold with Water Jacket of a High Speed Gasoline Based on FSI -- Design and Optimization on the Steel Rope Automatic Tensioning Device of Mine Elevator -- Study on the Relationship between Impeller Design Parameters and Performance of Partial Emission Pump Based on CFD Technology -- The Optimization of Suspension's Bushing Mounting Direction -- Identification of Surface Crack in Steel Rods Using Wavelet Transform Modulus Maximum on Vibration Mode -- Lightweight Design of Outer Wing Based on Importance Evaluation Factor -- Topology Optimization of QY70G Truck Crane Turntable Structure -- Design of Thin Wall Telescopic Space Mast Based on Self-Assembly of Steel Band -- Numerical Simulation for the Spray Field in Absorption Refrigerator for Automotive Air-Conditioning -- Discussions of Influence of some Factors on New Vehicle Absorption Cold Source -- Study on the Optimum Angle for Solar Collector -- The Reliability Analysis of Wheel Groove Milling Machine's Column Based on Probability Finite Element Method -- Comprehensive Analysis of C.I. Engine Fueled with Methyl Esters of Karanja Oil -- Methods of Low Passive Intermodulation Design -- Chapter 7: Materials and Processing Technologies of Materials in Mechanical Engineering -- Nonlinear Variation Analysis of Compliant Sheet Metal Assemblies Including Effect of Surface Continuity in Components -- Projectile Material Model Included Phase Transformation Erosion -- Research on Manufacturing Technics of New Low-Carbon Green Packaging Materials -- Stress Analysis of Isotropic Material Flywheel Battery Rotor -- Stress Fields and Energy Analysis during the Fracture of Composite Materials.

Tensile Strength Characteristic of Al6061-T6 and Al7003-T6 Aluminum by the Change in the Friction Welding Process Variable.

Selected, peer reviewed papers from the 2013 3rd International Conference on Mechatronics and Applied Mechanics (ICMAM 2013), December 27-28, 2013, Paris, France.

Description based on publisher supplied metadata and other sources.

Electronic reproduction. Ann Arbor, Michigan : ProQuest Ebook Central, 2024. Available via World Wide Web. Access may be limited to ProQuest Ebook Central affiliated libraries.